Tone Generator
Tone Generator is a great tool for locating and identifying cable pairs or individual conductors.
162 CB-G doesn't only provide the function of a tone generator, but also serves as a continuity and polarity tester.
A tone selector switch located inside the unit for selection of the fast tone or the slow tone.
Two bi-colored LEDs for Line1 and Line 2 indication of the polarities of the telephone lines.
The unit has alligator type terminals, a modular cable of 4 conductors with a strong connector.
The tone and continuity functions are only applied to Line1. (Modular connector)

Filter Probe
Works with any Tone Generator to identify wires.
Volume control for increasing sensitivity and adjustable to suit work environment.
2 operation modes: Filter on / Filter off.
The auto-off function (5 minutes) prevents battery consumption.
Power supply is available in any 9V battery with a life of approximately 50 hours.
A phone jack is designed for headset or handset.
Flashlight function.

Accessories
Instruction manual
Soft pouch
Batteries

Tone Generator
Wave form: Square Wave.
Frequency: 1kHz±15%.
Over voltage protection: 80V DC.
Alternating tone: Fast and Slow.
Connection: RJ11 connector, alligator clip x 2, RJ45 connector (optional).
Power source: 9V battery × 1.
Dimensions: 86(L)×63(W)×26(D)mm.
Weight (battery included): Approx. 130g.

Filter Probe
Operation mode:
Filter on (avoid the interference of 50Hz/60Hz),
Filter off.
Receiver distance: < 50cm
Sensitivity control
Probe tip: Fixed
Power source: 9V battery × 1
Dimensions: 250(L) × 39(W) × 38(D)mm
Weight (battery included): Approx. 180g

General
Operating temp & humidity: 0˚~40˚C, 80% Max.
Storage temp & humidity: -10˚~50˚C, 80% Max.

Safety Standard
EN 61326-1
EN 61000-4-2
EN 61000-4-3.

Tone Generator
Tone Generator is a great tool for locating and identifying cable pairs or individual conductors.
162 CB-G doesn't only provide the function of a tone generator, but also serves as a continuity and polarity tester.
A tone selector switch located inside the unit for selection of the fast tone or the slow tone.
Two bi-colored LEDs for Line1 and Line 2 indication of the polarities of the telephone lines.
The unit has alligator type terminals, a modular cable of 4 conductors with a strong connector.
The tone and continuity functions are only applied to Line1. (Modular connector)

Filter Probe
Works with any Tone Generator to identify wires.
Volume control for increasing sensitivity and adjustable to suit work environment.
2 operation modes: Filter on / Filter off.
The auto-off function (5 minutes) prevents battery consumption.
Power supply is available in any 9V battery with a life of approximately 50 hours.
A phone jack is designed for headset or handset.
Flashlight function.

Accessories
Instruction manual
Soft pouch
Batteries

Tone Generator
Wave form: Square Wave.
Frequency: 1kHz±15%.
Over voltage protection: 80V DC.
Alternating tone: Fast and Slow.
Connection: RJ11 connector, alligator clip x 2, RJ45 connector (optional).
Power source: 9V battery × 1.
Dimensions: 86(L)×63(W)×26(D)mm.
Weight (battery included): Approx. 130g.

Filter Probe
Operation mode:
Filter on (avoid the interference of 50Hz/60Hz),
Filter off.
Receiver distance: < 50cm
Sensitivity control
Probe tip: Fixed
Power source: 9V battery × 1
Dimensions: 250(L) × 39(W) × 38(D)mm
Weight (battery included): Approx. 180g

General
Operating temp & humidity: 0˚~40˚C, 80% Max.
Storage temp & humidity: -10˚~50˚C, 80% Max.

Safety Standard
EN 61326-1
EN 61000-4-2
EN 61000-4-3.